Ray Kulikowski asked 6 months ago
Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to auto locksmiths with experience with the right tools and know-how. They will be able to make and program new keys much quicker than a dealership and at a cheaper cost.
A dead battery for your coin is most likely to be at fault the reason why your key fob isn’t locking or unlocking doors. However, there are other reasons the key could be malfunctioning.
Dead Coin Battery
A dead battery can stop your Peugeot 208 from locking and unlocking, as well as stopping it from starting the engine. If this is the case, you’ll have to make use of the backup starting procedure which is explained in the owner’s manual to your vehicle.
The spark plugs may also be worn out. The spark plugs are responsible for igniting the fuel which starts the engine. They have a limited lifespan. They’ll eventually break down if they’re not used enough.
There is a simple solution to this issue. Check the voltage of your battery with a multimeter. If it is below 11.5 Volts it is time to replace it. It is also important to clean the contacts of the battery in the event that it is damaged by corrosion. This can be done by lifting the rubber covers covering the two battery terminals and using a wire brush to remove any corroded areas of the battery. Then, you should connect the cables that connect the positive and negative poles.
Water Damage
If your 208 will not start and the battery has not been replaced, you must look at the spark plugs. It could be that they are simply too dirty and they don’t spark. This is easily fixed by cleaning the spark plugs in the workshop.
Peugeot cars have a transponder style key that integrates with the car’s immobiliser system. This ensures that only the correct key can turn the engine. If the chip inside the Peugeot key is damaged, it won’t send the correct signal to the vehicle.
Water damage is a frequent cause of this issue. This is a typical issue in more cold climates where the car has been exposed to snow or rain. In this instance, you should contact a trusted locksmith who has the tools and equipment required to reprogram the key. They will also have the latest technology and equipment needed to make a Peugeot smart key. The process shouldn’t last more than 15 minutes.
Faulty Battery Contacts
peugeot key code (yogicentral.science) replaced the transponder chips by introducing a new model that is based on electronic components mounted on a circuit board. The new system works great in its initial state, but the circuit boards wear out over time and cease to function properly.
This can prevent the immobiliser from triggering so that the vehicle won’t start. If this is the case, it’s recommended to get in touch with a Peugeot specialist or locksmith.
A common problem is when the battery in the key fob starts to fail. This causes the blade of the key to stop feeding into the lock. A locksmith from your car will replace the battery and then cut a fresh blade for you. This is a quick fix.
Faulty Receiver Module
It could be that the receiver module is faulty if your Peugeot key fob fails to function after being dropped on the floor, exposed to a stormy rainstorm, or accidentally washed. The receiver module is responsible for transmitting radio signals to the onboard computer which regulates the central locking system of your Peugeot vehicle.
The key fob itself has rubber seals to prevent water from getting to the electronic chip inside. However prolonged exposure to water can cause damage to these seals and the chip. Submerging the key fob into ocean water on the beach or throwing it into the pool could be especially damaging because of the high salt content.
If your Peugeot spare key fob doesn’t work then you’ll have to get the module replaced. This is only done by an expert auto locksmith or peugeot 108 key specialist. Like other automobiles, Peugeot keys are protected by a unique immobilizer system that requires the correct coding in order to start the engine. This is why it is imperative that you should only trust an authorized Peugeot locksmith to create and program the replacement.
Faulty on-Board computer
The on-board computer in your Peugeot is responsible for a number of the systems in your vehicle, from airbags to power windows. If something is wrong with these systems, it’ll typically show a code that identifies the problem. The code is stored within the system and will stay there until the issue has been resolved. This can often mean that the on-board computers to be replaced.
The most common reason for the warning light for the airbag to turn on is corrosion or loose connections in the sensor. This could be due to wear and tear, ageing, or exposure to moisture and salt. This issue needs to be addressed as soon you can, since an airbag that’s malfunctioning could be dangerous in the event of an accident.
If you encounter an error message stating that the card is not found on your Peugeot key fob, the battery in the key fob might be weak or dead. This can prevent the key fob from sending a signal that disarms the immobilizer on your vehicle’s standard. Test this by pressing the unlock key on the fob’s key and then trying to start your car. If this does not work, then the key battery must be replaced.